Webertai Flex
Rated 5.00 out of 5 based on 1 customer rating
(1 Reviews)
Webertai flex adhesive cement is a flexible tile adhesive suitable for ceramic tiles, granite, marble, granite, artificial stone. We sell at project prices, only for contractors and project work.
LINE ID: @aycon
Tel: 083-0243351
Categories: Cements, Weber cement
Tags: weber, weber tile cem, Terracotta tiles, Ceramic tiles:, Cement glue, Laying tiles, Weber, Weber Tile Cem, Granite
Description
Weber Tile Flex adhesive cement
Flexible tile adhesive, high quality, single component type, easy to use, just mix with water. Contains cement, specially selected sand and special chemicals, increasing flexibility. Suitable for laying tiles, plywood, cement plywood, fiber cement.
Suitable for: Ceramic tiles, granite, marble, granite, artificial stone, size up to 1x1 meter.
Size: 20 kg per bag
color: grey
Usage volume: Average 4 sq m per 20 kg bag.
How to use
Surface preparation:
- For new surfaces: The surface must be smooth, hard, level, clean, dry and have normal water absorption.
- For existing surfaces: Check the surface by scraping off any loose paint or removing loose tiles and laying new ones. Remove any debris such as cement powder, fat, or oil stains stuck to the surface.
- If the surface is very porous (high water absorption), it is necessary to wet and saturate the surface with water before laying the tiles.
- If the surface is a plastered or newly applied cement wall: the standard curing time (i.e. 7 days per 1 cm. of thickness) should be used before laying tiles.
Mixing
Mix Weber Tile Flex cement glue with water at a ratio of 1 : 3 by volume.
(1 part water, 3 parts cement glue) Use a blender at low speed to blend until smooth, or divide and mix a little at a time and stir thoroughly until the glue does not clump. Leave for 3-4 minutes before using.
Tiling
- Use a trowel to spread the cement glue onto the surface.
- If the tile is larger than 10x10 inches, spread a thin layer of cement glue over the back of the tile.
- Lay the tiles on the cement glue and tap them all over with a rubber hammer.
- Wipe off any cement glue that has leaked out of the grout lines and that has stained the surface of the tiles.
- Customize your tiles in 15 minutes
- Leave for 24 hours before grouting.
Shelf life and storage
Shelf life and storage
1 year from the date of manufacture, in unopened condition and stored in a cool, dry, well-ventilated place. (If you don't use up all the bag, you must tie the bag tightly.)
type | Standard cement glue |
density | 1.40 g/cm2. |
Chemical curing period | 3-4 minutes |
Shelf life after mixing (store in a shady place) | 4 hours |
The time taken between applying cement glue and laying tiles | 20 - 30 minutes |
Tile alignment and adjustment can take a long time. | 15 minutes |
Thickness of cement glue spread on the surface | 2-10 mm. |
Before grouting the tile joints, allow the cement glue to dry for at least | 24 hours |
note : These test results are obtained from sample laboratories and may differ from the results obtained fromMixing at different agencies due to different usage methods and agency conditions.
See other types of cement products >>
Contact a sales representative:
LINE ID: @aycon
Tel: 083-0243351
Request for quotation
Additional information
| Types of cement work |
tile adhesive |
|---|---|
| Brands |
Weber |
Reviews
5
Rated 5 out of 5
1 review
Rated 5 out of 5
1
Rated 4 out of 5
0
Rated 3 out of 5
0
Rated 2 out of 5
0
Rated 1 out of 5
0
1 review for เวเบอร์ไทล์ เฟล็กซ์
Clear filters
Add a review Cancel reply
Red Brick calculation program

Archer –
Good service