Webertai Gres
Rated 5.00 out of 5 based on 1 customer rating
(1 Reviews)
Webertai Gres Cement Adhesive: High quality cement adhesive for laying large tiles and swimming pool tiles. Suitable for ceramic tiles, granito, marble, and granite. We sell at project prices, only for contractors and project work.
LINE ID: @aycon
Tel: 083-0243351
Categories: Cements, Weber cement
Tags: weber, swimming pool tiles, Ceramic tiles:, large tiles, Cement glue, Tile cement glue, High quality, cement, sand, Laying tiles, tile adhesive, Terracotta tile adhesive, Ceramic tile adhesive, Mix with water, marble, artificial stone, Granite, chemical, Weber, Webertai Vis, sticky, Granite, High adhesion strength, Easy to use, Tile Grace
Description
Weber Tile Grace Adhesive
High quality cement glue for laying large tiles and swimming pool tiles. Single component type. Easy to use, just mix with water. Contains cement, specially selected sand, and special chemicals. Strong and has 4 times higher adhesion strength.
Suitable for: Ceramic tiles, granite, marble, granite, artificial stone, size up to 1.20x1.20 m.
Size: 20 kg per bag
color: Gray/White
Usage volume: Average 4-7 sq m per 20 kg bag.
How to use
Surface preparation:
- For new surfaces: The surface must be smooth, hard, level, clean, dry and have normal water absorption.
- For the original surface: Check the surface for any loose paint or remove loose tiles and re-lay them. Remove any debris such as cement powder, fat, or oil stains that are stuck to the surface.
- If the surface is very porous (high water absorption), it is necessary to wet and saturate the surface with water before laying the tiles.
- If the surface is a plastered wall or newly leveled cement: the curing time should be in accordance with the standard. (7 days per 1 cm. thickness) before laying tiles
Mixing
Mix Weber Tile Grease cement glue with water at a ratio of 1:3 by volume (1 part water, 3 parts cement glue). Use a low-speed blender to blend until smooth, or divide and mix a little at a time and stir thoroughly until the glue does not clump. Leave for 3-4 minutes before use.
Tiling
- Use a notched trowel to spread the cement glue onto the surface.
- If the tile is larger than 10x10 inches, spread a thin layer of cement glue over the back of the tile.
- Lay the tiles on the cement glue and use a rubber hammer to knock them all over.
- Wipe away any excess cement glue that has spilled out of the grout lines and that has stained the surface of the tiles.
- Customize your tiles in 15 minutes
- Leave for 24 hours before grouting.
Shelf life and storage
1 year from the date of manufacture, in unopened condition and stored in a cool, dry, humid place with good ventilation. (If you don't use up all the bag, you must tie the bag tightly.)
type | Standard cement glue |
density | 1.40 g/cm2. |
Chemical curing period | 3-4 minutes |
Shelf life after mixing (store in a shady place) | 4 hours |
The time taken between applying cement glue and laying tiles | 20 - 30 minutes |
Thickness of cement glue spread on the surface | 2-10 mm. |
Before grouting the tile joints, allow the cement glue to dry for at least | 24 hours |
note : These test results are obtained from sample laboratories and may differ from the results obtained fromMixing at different agencies due to different usage methods and agency conditions.
See other types of cement products >>
Contact a sales representative:
LINE ID: @aycon
Tel: 083-0243351
Request for quotation
Additional information
| Types of cement work |
tile adhesive |
|---|---|
| Brands |
Weber |
Reviews
5
Rated 5 out of 5
1 review
Rated 5 out of 5
1
Rated 4 out of 5
0
Rated 3 out of 5
0
Rated 2 out of 5
0
Rated 1 out of 5
0
1 review for เวเบอร์ไทล์ เกรส
Clear filters
Add a review Cancel reply
Red Brick calculation program

Boss –
It works well.